Stop Lot Rust on Brake Rotors: How Rotor Coater Works (and What It Won't Do)

After a rotor is resurfaced, or when a shop fits an uncoated rotor, the bare metal is left open to the weather. That is where shops use Rotor Coater most. It is a fine-particle zinc spray, made by Moto Solutions, applied to the rotors and left to dry. It gives the rotor a premium-looking finish and helps protect it from the elements. It is a more premium choice than ordinary rotor paint, because those fine zinc particles get into the porous metal.

It can also help prevent the lot rust you see when a finished vehicle sits for a few weeks, or when a freshly machined rotor sits in a damp bay before delivery. It does not make rust impossible. This post explains how it works, what you should expect after a test drive, and what it will not do.

Why brake rotors rust after machining, and when a vehicle sits

Brake rotors are bare metal. After a rotor is resurfaced, or when an uncoated rotor is fitted, moisture in the air starts to rust the exposed surface. You will see it on the friction face, and often on the hat and the cooling fins as well. The same thing can happen when a car or truck sits on a dealership lot or in a storage yard.

Freshly cut rotors rust especially easily, because machining leaves a clean, unprotected face. That is one reason shops coat the rotor right after the lathe work, not a week later. If you are deciding whether a rotor should be machined or replaced in the first place, we walked through that in when to resurface or replace brake rotors.

Rotor Coater will not change the weather. It is a practical way to give the rotor a better-looking finish and help protect it from the elements.

What Rotor Coater is

Brake rotor coated with Rotor Coater spray

Rotor Coater is a fine-particle zinc spray, made by Moto Solutions and sold in a 400 ml aerosol can. Shops use it mostly on resurfaced or uncoated rotors. A light coat gives a premium-looking finish and helps protect the rotor from the elements. It is also used, as a secondary step, on vehicles that will sit on a lot or in storage.

The directions are simple: clean the rotor surface, shake the can, and apply a light, even coat. Let it dry for 10 to 15 minutes before a test drive or before the vehicle is driven.

It is sold as a single can, a 12-pack, and a starter pack that includes the 12-pack plus a can holder with mounting hardware. The holder is made in Canada from stainless steel, and it mounts on a brake lathe, a workbench or a toolbox.

Rotor Coater vs. Regular Rotor Paint

Shops sometimes reach for brake rotor paint, or a brake rotor coating spray, to protect a freshly cut rotor and improve the finish. Typical paints sit on the surface. Rotor Coater is a more premium rotor coating: its fine zinc particles get into the porous metal, and it still gives the rotor a premium-looking finish.

What happens on a test drive

Once the spray has dried for 10 to 15 minutes, the vehicle can be test driven. On a road or test drive, much of the coating burns off the friction surface. More of it comes off on a longer drive, which is normal. The friction face still has to work as a brake, so you should not expect the visible coating to stay there.

That does not mean the treatment has worn away completely. The fine particles get into the porous metal of the rotor. The coating also stays on the hat and the cooling fins, which do not see the same heat and friction. That is why it still helps prevent rust, even after the face looks closer to a normal rotor again.

What Rotor Coater will not do

It will not make rust impossible. A vehicle that sits outside for a long stretch, especially in wet or salty conditions, can still show rust. Rotor Coater helps protect the rotor from the elements and helps prevent rust. It is not a guarantee that a rotor will stay clean forever.

It is also not a substitute for a proper brake job. If a rotor needs to be machined or replaced, coat it after that work is done, not instead of it. A Pro-Cut on-car brake lathe, such as the Pro-Cut PFM X9, cuts the rotor while it is mounted on the vehicle, so the finished surface is matched to that hub. After the cut, a light coat of Rotor Coater is a sensible last step, both for the finish and for protection from the elements.

Frequently asked questions

Can the customer test drive the vehicle after Rotor Coater is applied?

Yes. Let it dry for 10 to 15 minutes, then the vehicle can be test driven.

Will the customer still see the spray on the rotors?

After a drive, much of it burns off the friction surface, especially on a longer drive. It stays on the hat and the cooling fins, and the fine particles remain in the porous metal.

Does Rotor Coater stop rust completely?

No. It gives the rotor a premium-looking finish and helps protect it from the elements, including the lot rust you see on vehicles that sit. It does not make rust impossible.

Is Rotor Coater the same as rotor paint?

No. Typical paints sit on the surface. Rotor Coater is a more premium zinc spray. Its fine particles get into the porous metal, and it gives the rotor a premium-looking finish.

Can it be used on electric and hybrid vehicles?

Yes. Rotor Coater can be used on electric and hybrid vehicles. Regenerative braking means the rotors are used less, so they can rust more than rotors that are braked more often.

Talk to us

If you want to use Rotor Coater in the shop, after resurfacing, or on uncoated rotors, contact Moto Solutions. You can call 1-866-236-6008 or email info@motosolutions.ca. We are in Sunderland, Ontario, and we work with dealerships, fleets and repair shops across Canada.

Use code ROTORCOAT15 for 15% off your first Rotor Coater order (one use per customer).